How Much Does Well Pump Replacement Cost in Texas?

Quick Answer

Submersible well pump replacement in Texas typically costs $1,200–$4,500 for most residential systems, including pull, pump, and reinstall.

When a well pump fails in North Texas, most homeowners have no water within hours of the failure — which means replacement can’t wait. Submersible pump replacement for a typical residential well runs $1,200–$4,500, depending on depth, pump size, and whether any wiring or drop pipe needs to be replaced.

What Affects Well Pump Replacement Cost

Well Depth

Depth is the biggest variable. A pump in a 150-ft well can be pulled quickly by hand or with a lightweight service rig. A pump at 400 ft requires a service truck with a hydraulic reel and specialized pulling equipment. More labor, more materials (drop pipe), more time — all of which add cost.

Well Depth	Typical Replacement Cost
Under 150 ft	$1,200–$2,000
150–300 ft	$1,800–$3,000
300–500 ft	$2,500–$4,000
500 ft+	$3,500–$5,500+

Pump Horsepower and Flow Rate

Pump size is determined by your well’s yield and household water demand:

½ hp pump (small household, shallow well): $400–$700 for the pump
¾ hp pump (average household): $500–$900 for the pump
1 hp pump (large household or irrigation): $700–$1,400 for the pump
1½–2 hp pump (high demand or deep well): $1,000–$2,000+ for the pump

Pump cost is added to the pull-and-reinstall labor.

Drop Pipe and Wiring

If the polyethylene drop pipe or submersible cable has deteriorated, it’s replaced during the pump job. Poly pipe runs approximately $1.50–$3.00/ft and submersible wire runs $1.00–$2.50/ft — on a 300-ft well, plan for $750–$1,650 in pipe and wire materials if both need replacing.

Signs Your Pump Needs Replacement

No water at all — pump may have seized or lost power
Water sputters and stops — loss of pressure, possibly pump or pressure tank
Rapid pressure cycling — pump short-cycles due to failed tank bladder (replace the tank)
High electricity bills — pump running continuously due to failure to build pressure
Sandy or gritty water — pump is pulling sediment (pump screen or well itself may be compromised)
Pump older than 12–15 years — proactive replacement is typically more economical

What a Licensed Contractor Includes

Texas law requires all pump work to be performed by a TDLR-licensed driller or pump installer. A licensed contractor will:

Pull and properly dispose of the old pump
Size the new pump correctly for your well’s depth, yield, and household demand
Pressure-test after installation before leaving
Provide documentation of the new pump model and installation date

That documentation matters when selling the property or making insurance claims.

Call for Same-Day Service

Well pump failure is a same-day emergency for most households. We carry common pump sizes and motors in stock for rapid response across all 19 counties in our North Texas service area — including Wise, Cooke, Denton, Parker, Hood, and Erath.

Frequently Asked Questions

How much does it cost to replace a submersible well pump in Texas?

A full submersible pump replacement — pulling the old pump, supplying and installing a new pump and motor, and reinstalling with new drop pipe and wiring — typically costs $1,200–$4,500 for most residential systems in North Texas. Shallow wells (under 200 ft) with lower-horsepower pumps run toward the lower end; deep wells (400+ ft) requiring a 1-hp or larger pump run $2,500–$4,500 or more.

What is included in a well pump replacement?

A complete pump replacement job typically includes: pulling the existing pump and drop pipe from the well, supplying and installing a new submersible pump and motor (sized to your well depth and household demand), new polyethylene or steel drop pipe, new safety cable, new electrical wiring from the pump to the control box, and reconnection to your pressure system. Pump replacement does not automatically include replacing the pressure tank — that's usually quoted separately.

How do I know if my well pump needs to be replaced vs. repaired?

Common signs a pump needs replacement rather than repair include: no water at all (pump may have seized or failed), water sputtering or cycling rapidly (pump losing prime or pressure tank failed), grinding or burning smell from the control box, sudden high electricity bills from a pump running continuously, and water that appears sandy (pump screen may be blocked or the pump is pulling from the bottom of a silted well). A pump that's more than 10–15 years old with any of these symptoms is usually more economical to replace than repair.

How long do well pumps last in North Texas?

Most submersible pumps last 10–15 years in normal residential service. In North Texas, pumps in wells with high iron or mineral content (common in Erath, Hood, Parker, and Palo Pinto counties) may wear faster due to abrasive particles. Pumps that cycle frequently due to a failed pressure tank bladder also wear out faster. Annual inspection catches declining performance before a total failure leaves you without water.

Does the pressure tank need to be replaced at the same time as the pump?

Not necessarily, but it's worth inspecting. If your pump is 10+ years old and has failed, there's a reasonable chance the pressure tank bladder has also deteriorated. Replacing both at the same time avoids a second service call and typically saves on labor. A new pressure tank (20–44 gallon) costs $300–$700 in parts; installation adds $200–$400 in labor if done during a pump job versus a separate visit.

Can I replace a well pump myself in Texas?

Texas law requires that any work on a water well — including pump installation and replacement — be performed by a licensed water well driller or pump installer holding a current TDLR license. DIY pump replacement is not legal and can void manufacturer warranties. Unlicensed work can also create liability issues when selling the property or making insurance claims.

Get a Realistic Cost Conversation

Cost depends on a lot of factors. Share your property details so we can have a useful conversation.